Black Atlas Series Hydraulic Jack Plate

$2,075.00$2,399.00

-

Description

Black Atlas Series Hydraulic Jack Plate

Features

NOTE: SOME JACK PLATES ARE MADE TO ORDER, WHICH CAN TAKE UP TO 4-6 WEEKS. PLEASE CONTACT US FOR STOCK INFORMATION

Featuring advanced hydraulic technology, this Black Atlas Series Jack Plate allows you to effortlessly adjust the height of your outboard motor. Experience seamless and precise control over your boat’s trim and tilt, allowing you to adapt to varying water conditions and maximize performance.

The Atlas revolutionary design meets the demands of today’s high performance outboards. The one piece design, featuring the innovative Rod and Slot lifting system, will handle the stresses from the heaviest and most powerful outboards, up to 300 HP or 625 pounds, on the market today.

All of the hydraulics are built into the jack eliminating the necessity of installing pumps and reservoirs inside the transom. The all new hydraulic unit is fast too..lifting from bottom to top in 8 seconds!

Transom side of the atlas is 16 3/8″ wide x 12 1/2″ tall.

NOTE: mounting bolts are not included

OEM/Bulk Product Name Distributor Packaged
AHJ-4V-B-DP Atlas Series™ Hydraulic Jack Plate – 4″ Setback – Black AHJ-4V-DP
AHJ-6V-B-DP Atlas Series™ Hydraulic Jack Plate – 6″ Setback-Black AHJ-6V-DP
AHJ-8V-B-DP Atlas Series™ Hydraulic Jack Plate – 8″ Setback-Black AHJ-8V-DP
AHJ-10V-B-DP Atlas Series™ Hydraulic Jack Plate – 10″ Setback-Black AHJ-10V-DP
AHJ-12V-B-DP Atlas Hydraulic Jack Plate – 12″ Setback – Weight 66lbs-Black AHJ-12V-DP
AHJ-14V-B-DP Atlas Series™ Hydraulic Jack Plate – 14″ Setback-Black AHJ-14V-B-DP

Please note: The yellow ruler sticker is just a visual reference for the driver.  On the Heavy Duty Atlas jack plates the yellow ruler sticker will show approximately 4 ¼” of lift. That is due to the black polymer rods being taller on the Heavy Duty Atlas jack plates and the 1” of lift that is built in to the plate.  The standard Atlas jack plates will show 5” of lift, due to the 1” of lift that is built in to the plate.  To confirm the 5 ¾” of hydraulic lift just raise the jack plate all the way up and measure the hydraulic actuator piston.

    • Max Weight: 625 lbs
    • Max Horsepower: 300 hp
    • Max Horsepower (Heavy-Duty Version): 400 hp
    • Width: 16 3/8″
    • Height: 12 1/2″

NOTE: SOME JACK PLATES ARE MADE TO ORDER, WHICH CAN TAKE UP TO 4-6 WEEKS. PLEASE CONTACT US

5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE

ATLAS™ is truly the best hydraulic jack plate in the world

ATLAS™ is factory installed by more boat manufacturers than any other plate

ATLAS™ is used by more professional fisherman than any other hydraulic jack plate

ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets

ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China

6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER

ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied

ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied

ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that

ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure

ATLAS™ was the first plate to offer a very simple actuator replacement in the field

ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement

OEM/Bulk Product Name Distributor Packaged
AHJ-4V-DP Atlas Series™ Hydraulic Jack Plate – 4″ Setback AHJ-4V-DP
AHJ-6V-DP Atlas Series™ Hydraulic Jack Plate – 6″ Setback AHJ-6V-DP
AHJ-8V-DP Atlas Series™ Hydraulic Jack Plate – 8″ Setback AHJ-8V-DP
AHJ-10V-DP Atlas Series™ Hydraulic Jack Plate – 10″ Setback AHJ-10V-DP
AHJ-12V-DP Atlas Hydraulic Jack Plate – 12″ Setback – Weight 66lbs AHJ-12V-DP
AHJ-14V-DP Atlas Series™ Hydraulic Jack Plate – 14″ Setback AHJ-14V-DP

Please note: The yellow ruler sticker is just a visual reference for the driver.  On the Heavy Duty Atlas jack plates the yellow ruler sticker will show approximately 4 ¼” of lift.  That is due to the black polymer rods being taller on the Heavy Duty Atlas jack plates and the 1” of lift that is built in to the plate. The standard Atlas jack plates will show 5” of lift, due to the 1” of lift that is built in to the plate.  To confirm the 5 ¾” of hydraulic lift just raise the jack plate all the way up and measure the hydraulic actuator piston.

HEAVY DUTY VERSION ALSO AVAILABLE

T-H Marine’s ATLAS™ hydraulic jack plate is truly the next generation in jack plate design, built for the heaviest and most powerful outboard engines on the market today, even the big four strokes. Our innovative high tech engineered polymer rod and slot lifting design guarantees trouble free action. This plate also features the newest concept in one-piece hydraulics from the most respected name in hydraulic design, providing the best of all worlds: Speed and Self contained lifting action. This all new pump will lift the heaviest outboard from bottom to top in less than 8 seconds.

Self Contained Hydraulic Pump System (No Reservoir or lines to install) Hydraulic actuator is made in the U.S.A. Fast!

NOTE: mounting bolts are not included

Specs

  • Max Weight: 625 lbs
  • Max Horsepower: 300 hp
  • Max Horsepower (Heavy-Duty Version): 400 hp
  • Width: 16 3/8″
  • Height: 12 1/2″

Additional information

Setback

4", 6", 8", 10", 12"